top
  • Yongkang Lion Stainless Steel Products Co., Ltd.
banner
Contact us

Address:Zhejiang province Yongkang City Gushan IndustrialIndustry zone (321307)

Phone:0579-87066018

87066028

87066038

88020588

87066742

87066048

Fax:0579-88020566

87066741

Contact person:

桑泽良 13857023607

叶美子 13858936713

诚信通:zjxs2012

lioncups

zjxs2010

E-mail:yemeizi00@163.com

E-mail:chinacup@126.com

在线联系雄狮
在线联系雄狮
Video
Partner
Microblogging
Thermal Mug knowledge(Hits:) 
Origin Author Add Time2012-06-16
fontSize: T|T
Why I tested the temperature of the page - the subject of insulation effectiveness or cold effect
A: The insulation effect or cold effect varies with changes in the test environment.
The subject of insulation effectiveness or cold effectiveness test conditions are:
Insulation effect is filled with room temperature at 20 ° C water temperature above 95 ° C hot water to the bottom of the bolt, put to the test one hour after the water temperature in the product erection of wind conditions.
The cold effect below room temperature at 20 ° C water temperature 4 ° C cold water filled bottle the bottom, in the erected state of the product, place six hours after the water temperature.

The picture looked almost the size of the insulation cup, why the kind so small or so big ah.
A: The images are not displayed according to the ratio of 1:1, so please bring your own ruler before buying (online shopping necessary), infer the size rather than the seat of your pants to determine the size to avoid is not suitable for trouble .
The shop provided the size and weight due to the amount taken, does not exclude a different take with you the amount of (3CM) size fine, go to the mall counters to look at the physical, and then decide to buy.

Plastic parts protruding point or linear, wavy, or dent a small point, like a small scar, I think it is flawed!
A: The kind of problem is the requirements of the injection mold process, the purpose is to facilitate the demolding of the parts or injection molding. Each product will have, just maybe different sizes, in varying degrees. Two leaves (the world does not exist on exactly the same, but as long as it is certainly the same components will have no effect on the quality if you do not understand this, please do not buy.
4 plastic parts to wear away, wear scar, when the arts and crafts to buy, and you can not accept?
Answer: because of the particularity of the plastic in the production assembly, manual packing, long-distance transport process slight grinding paint may result in slight traces. (We can nail a slight test program to see even gently, are can leave traces of) these parts really have a little bit of this problem, is not considered as defects
I measured the size and weight and you the amount of Why?
A: size and weight due to the different amount of law, not rule out the possibility that a subtle error.
6. Lid tighten the friction sound, why?
A: Tighten the lid and the cup due to friction will certainly sound, buy the mall, too, too sensitive, please carefully.
7 cup mouth parts of the paint did not sprayed faulty?
A: Thermal Mug colored spray in the cup neck transition area may be uneven phenomenon, processes and technologies can not be achieved, is a normal situation.
8 Why is the gap between the lid and the cup?
A: between the cup and the lid, the lid seals elasticity of the reason is not very uniform, which is normal to the mall to buy is the same.
Why the outside or interior side seems to have a protruding or sunken traces? Some minor scratches Oh?
Answer: a lot of cup molding, and some can directly stretch, some welding
Why stainless steel surface will be some small lines, marks or trachoma, I do not have any flaws.
A: The stainless steel sheet rolling with plate pattern, but some polishing time can be disposed of, but do not rule out also left a little
11 Why do some cup is not very round, one or several locations slight inward or outward turning, or a wave pattern
A: Some of the cup is a single layer stainless steel design (not a double or curling design), general insulation products stainless steel thickness of about 0.8-1.3mm or so, if after the incision, single-layer cup flash, grinding and polishing process or other processes, are likely to than other double cup is easy to cause a slight (very slight) deformation, as long as it does not affect the appearance and use depends on qualified and factory. (If we find that the problem is serious and obvious product is shipped.)

Why paint products sometimes have one or two points is not sprayed into the bottom of the cup edge of the painting is not very neat? Some pattern of the product why LOGO and pattern of the surrounding traces?
A: The painting process is very complex, not simple. Sometimes spraying is not very uniform will result in this case, more than a point spray more paint or less a spray, but obviously the manufacturers not to ship, minor is deemed to be acceptable the. Another cup of drinking water position is not paint the bottom position is painted shut, the place where the hem is very, very difficult to do very neat, but the lid can cover not see This is the limitations of the technology, please Root of the Matter perfect to understand this point and then make a purchase.
Some products logo or pattern decal thermal printing, decal many times have the manpower posted up, artificial things may be posted was not very docile, or bits missing, it will make the product printing folds or slight dislocation. Another paper flower in the torn left the traces of a paper flower. But some mature technology, the factory can handle this problem would be better, please do not be too demanding.
13 plastic parts protruding point or linear, wavy, or dent a small point, like a small scar, I think it is flawed!
A: The kind of problem is the requirements of the injection mold process, the purpose is to facilitate the demolding of the parts or injection molding. Each product will have, just maybe different sizes, in varying degrees. Two leaves (the world does not exist on exactly the same, but as long as it is certainly the same components will have no effect on the quality if this do not know too much emphasis on flawless friends, it is recommended not to buy.
14 plastic parts to wear away, wear scar, I buy when the crafts, that are not acceptable?
Answer: because of the particularity of the plastic in the production assembly, manual packing, long-distance transport process slight grinding paint may result in slight traces. (We can nail a slight test program to see even gently, are can leave traces of) these parts really have a little bit of this problem, is not considered as defects. very picky perfectionist Bypass (obviously a serious product, we will not be shipped some slight extent as a normal and can be accepted.)

15 cups an open unpleasant odor is not the cup material is not good? In tied plastic material is not good?
A: insulated cup has been sealed with so just open the flavor wash quasi did
Any one insulated cup so that our home insulation cup directly down the production line open opened completely new if you bought an insulated cup in the supermarket, it is because long-term exposure to the outside then many customers will be open look at a transport delivery 304 stainless steel plus a PP is safe to eat the plastic bolt can smell where to go so do not always tangled insulation Cup have any unpleasant odor problem
keyworks:

bottom
    Copyright:Yongkang Lion Stainless Steel Products Co., Ltd.    Support:easthardware
Message